供应


智能制造网供应网 包装袋拉力试验机厂家

包装袋拉力试验机厂家

  • 产地
  • 所在地
  • 北京市
  • 北京北京市

更新时间:2024-03-28

有效日期:还剩183

产品详情

包装袋拉力试验机故障及解决方法:
Seven, fault and solution method:

一、拉力试验机加荷时,指针颤动或时走时停
A, tensile test machine, vibration or pause the pointer

1、离合器齿轮磨损:需要修理或更换。
1, the clutch gear wear: the need for repair or replacement.

2、摩擦盘的皮垫圈或弹簧磨损:需更换皮垫圈或弹簧。
2, the skin friction disc washer or spring wear: need to change the skin or spring washer.

3、操纵手柄移位:调整操纵手柄,使其与牙槽配合好。
3, handle shift: to adjust the control handle, make it fit in with the alveolar.

二、更换摆砣时指针不回零
Two, the replacement of pendulum weight when the pointer does not return to zero

1、拉力试验机安装不水平:用水平仪把试验机调整水平。
1, tensile testing machine installation is not level: the level to adjust the level of test machine.

2、摆锤不垂直:只挂A砣。调整平衡砣,使之垂直。
2, not only the vertical pendulum hanging weight: A. Adjust the balance weight, so that the vertical.

三、拉力试验机摆锤回位太快或太慢
Three, tensile testing machine, the pendulum back a bit too fast or too slow

1、缓冲阀挡位位置放置不当:调整缓冲阀到适当位置。
1, the buffer valve gear position placed improper: adjust the buffer valve to the appropriate location.

2、液压油黏度过低或过高:液压油黏度过低时摆锤回落快,黏度高时回落慢.应更换适当黏度的液压油。
2, the hydraulic oil viscosity is too low or too high: hammer down fast swing hydraulic oil viscosity is too low, viscosity is high down slowly. Should be proper replacement of hydraulic oil viscosity.

3、缓冲阀内、油管内或液压油有脏污:清洗缓冲阀、油管。更换液压油。
Vittae 3, buffer valve, or hydraulic oil dirty: washing buffer valve, pipe. Replacement of hydraulic oil.

四、拉力试验机指针回零滞怠或不稳定
Four, tensile testing machine pointer back to zero lag or unstable

1、指针轴承、主轴轴承锈蚀或有油污:清洗或更换轴承。
1, the pointer bearing, spindle bearing corrosion or oil: clean or replace bearing.

2、齿杆变形或齿杆与齿轮不啮合:校直齿杆或清洗、修整齿轮、槽轮等传动部件。
2, toothed bar deformation or toothed bar and gear is not engaged: straightening toothed bar or washing, dressing gear, wheel, transmission parts.

3、缓冲阀内有脏污:清洗缓冲阀。
3, the buffer valve with cleaning: cleaning buffer valve.

五、拉力试验机示值正偏差
Five, tensile testing machine showing the value of positive deviation

1、短臂刀刃有松动:把刀刃紧牢。
1, the short arm loose: the knife blade tightly.

2、摆砣偏轻:给砣配重(要兼顾A、B、C砣的重量)。
2, swing weight lighter: give weight weight (both A, B, C weight weight).

六、示值负偏差zui主要原因是各部件之间的摩擦阻力过大
Six, showing the value of negative deviation is the main reason of the frictional resistance between the units is too large

1、指针轴承、摆轴轴承和测力传动部件摩擦阻力过大:主要是调整、清洗轴承及测力传动部件.消除不正常的摩擦阻力。
1, the pointer shaft bearing, bearing and power transmission parts friction resistance is too large: mainly adjustment, cleaning bearings and force transmission parts to eliminate the friction resistance is not normal.

2、上夹头、从动针弹簧片松紧度和描绘装置的摩擦阻力大:调整上夹头、从动针弹簧片松紧度和描绘装置部件.消除不正常的摩擦阻力。
Friction resistance on 2, chuck, driven needle leaf spring tightness and describe the adjustment device: chuck, driven needle leaf spring tightness and drawing device components. To eliminate the friction resistance is not normal.

3、活塞杆与摆杆相接部位不灵活:调整两者相接部位。使之灵活自如。
3, the piston rod and the swing rod is connected with the flexible adjustment of both parts not connected parts. The flexible.

七、从动针滞阻或移位
Seven, the driven needle stagnation or shift

1、从动针弹簧片弹力大小或从动针与指示盘摩擦阻力大小造成的影响:调整从动针弹簧片的弹力或从动针与指示盘的问隙。
Effect of 1, driven needle leaf spring elastic force or driven needle and dial friction resistance caused by the gap adjustment driven needle: the elasticity of the spring piece or driven needle and dial.

2、从动针两端重鼍有偏差:调整两端重量,使其平衡。
2, the driven needle are heavy alligator deviation: adjusting the weights, the balance.

八、示值无规律的偏差
Eight, showing the value of deviation is irregular

1、齿杆、齿轮有油污、磨损或有毛刺:消除齿杆、齿轮的油污、毛刺,找出超差时的齿杆接触点,然后修正齿杆、齿轮;如不能消除误差.更换齿杆、齿轮。
1, rack, gear oil, abrasion or burr: eliminate the rack, gear oil, burr, find out the pole difference when the contact points, and then modified tooth bar, gear; if not eliminate errors. Replace the tooth bar, gear.

2、拉力试验机试验机安装不水平:调整水平。
2, tensile testing machine testing machine installation is not level: level adjustment.

3、齿杆弯曲:校直或更换齿杆,调整滚动槽轮的问隙。
3, toothed bar bending: alignment or replacement tooth bar, adjust the roll gap groove wheel.

九、计算机软件联机后出现提示框信息显示超载。
Nine, computer software on-line prompt box display information overload.

解决方案是检查计算机与试验机的通讯线是否脱落;检查联机选择传感器是否选择正确;检查zui近的试验或操作键
The solution is to check the computer and test machine communication line is off; check the online selection of sensor is correct; check the last test or operation keys

盘时传感器是否被撞过;检查出现问题之前是否使用了软件的校准或标定功能;检查是否手动更改过校准值、标定值或硬件参数中的其他信息。
When the sensor is knocked off; check whether the use of a software appears calibration or calibration before; check whether the manual modified calibration values, calibration information value or other hardware parameters in the.

十、试验机主机电源不亮,不能上下移动。
Host ten, the power of the testing machine does not light, not to move up and down.

解决方案是检查接入试验机的电源线路是否连接正常;检查急停开关是否处于拧起状态;检查接入试验机的电源电压是否正常;检查机器插座上的保险是否烧断,请取出备用保险丝安装即可。
The solution is power line inspection access testing machine is connected properly; check the emergency stop switch is in screwed up state; power supply voltage check access testing machine is normal; check the socket on the insurance is burned off, remove the spare fuse can be installed.

十一、试验机主机电源有电但设备不可以上下移动。
Host eleven, testing machine power supply with power but the equipment can not move up and down.

解决方案是检查是否是15S(时间)以后设备还无法移动,因为主机开机需要自检,大概需要15S时间;检查上下限位是否再恰当的位置,有一定的运行空间;检查接入试验机的电源电压是否正常。
The solution is to check whether it is 15S (time) after the device is unable to move, because the host boot take self-inspection, probably need 15S time; check the upper and lower limit is again appropriate position, operating space; check supply voltage access testing machine is normal.

 

售后服务及保修承诺:
多年来,我公司一直专业生产研究电气试验设备,经研究、摸索、总结出一套完整的产品服务保障体系,向用户提供优质及时的售前、售中、售后服务
为创造,提高企业度,树立企业形象,我们本着“一切追求高质量,用户满意为宗旨”的精神,以“*惠的价格、zui周到的服务、zui可靠的产品质量”的原则向您郑重承诺:

一、产品质量承诺:
1、我公司保证向需方提供的设备是原厂生产的,并且出厂资料配件齐全。为保持合同设备的正常运行和维护,我公司保证提供的技术资料和图纸是完整、清楚和正确的。
2、产品的制造和检测均有质量记录和检测资料。
3、对产品性能的检测,我们诚请用户亲临对产品进行全过程、全性能检查,待产品被确认合格后再装箱发货。

二、产品价格承诺:
1、为了保证产品的高可靠性和先进性,系统的选材均选用国内或优质产品。
2、在同等竞争条件下,我公司在不以降低产品技术性能、更改产品部件为代价的基础上,真诚以*惠的价格提供给贵方。

三:安装调试及验收承诺:
1、协助设备的安装,负责设备的运输、调试。
2、设备按订货技术附件进行验收。终验收在买方进行,对用户提供的试样进行试验,并提供测试报告。
3、安装调试同时,在仪器操作现场一次性免费培训操作人员2-3名,该操作人员应是由需方选派的长期稳定的员工,培训后能够对设备基本原理、软件使用、操作、维护事项理解和应用,使人员能够独立操作设备对样品进行检测、分析,同时能进行基本的维护。

四、保修承诺:
1、设备保修一年,终身服务,一年内非人为损坏的零部件免费更换,保修期内接到用户邀请后, zui迟响应时间为2小时内,在与用户确认故障后,我公司会在48小时内派工程师到达现场进行免费服务,尽快查清故障所在位置和故障原因,并向用户及时报告故障的原因和排除办法 。
2、保修期内人为损坏的零部件按采购(加工)价格收费更换。
3、保修期外继续为用户提供优质技术服务,在接到用户维修邀请后3天内派工程师到达用户现场进行维修。并享有优惠购买零配件的待遇。 
4、传感器过载及整机电路超压损坏不在保修范围内。

 

Beijing Beiguang precision instrument equipment Co., Ltd. - products:(series of electrical properties of rubber and plastics) voltage breakdown testing instrument, electrical strength tester, the dielectric breakdown strength tester, electronic universal testing machine, the surface resistivity tester volume resistivity, dielectric constant and dielectric loss tester, tracking test apparatus, verticalDirect combustion apparatus, rubber brittle low-temperature impact tester, melt flow index, melt flow rate detector, VEKA softening point temperature measuring instrument plastic deformation, sliding friction and wear testing machine, arc resistance test, Martin test instrument, building materials burning tester, ballIndentation hardness tester, Charpy test machine, electric blanket dynamic load testing machine, universal testing machine, punching machine, dumbbell system prototype, drop hammer impact, dart impact, falling ball impact test machine, index system(sponge foam series) sponge foam indentation hardness tester, falling ball rebound test machine, sponge cutting machine, sponge tensile strength testing machine, and the fatigue indentation test machine, compression testing machine, tear strength, rebound rate.After sale service and warranty:Over the years, our company has been specializing in the production of electrical test equipment, research, exploration, summed up a complete security system products and services, to provide quality and timely pre-sale, sale, after sale service to usersTo create a famous brand, increase brand awareness, establish a corporate image, we have the spirit of "all the pursuit of high quality, customer satisfaction as the purpose" of the spirit, to "the most preferential prices, the most attentive service, the most reliable product quality" principle solemnly promise to you:A, product quality commitment:1, our company to ensure that equipment to the need to provide the original factory, and the factory data complete accessories. In order to maintain normal operation and maintenance of contract equipment, our company guarantees to provide technical information and drawings are complete, clear and correct.2, product manufacturing and testing are quality records and test data.3, the product performance test, we ask the user to visit the whole process, the whole performance inspection of the product, the product is qualified after packing shipments.Two, the product price commitment:1, in order to ensure the high reliability and advanced products, systems material are selected domestic and international high-quality brand-name products.2, in the same competition condition, our company based on not to reduce the technical performance of products, product components for cost, provide the most preferential price to you.Three: debugging and installation acceptance commitment:1, assist the installation, transportation, commissioning of equipment.2, equipment for approval according to the order of the technical annex. Final acceptance in the buyer, for users of the test specimen, and provide the test report.3, installation and commissioning at the same time, the instrument operation on-site one-time free training 2-3, the operating personnel shall be appointed by the buyer to the long-term stability of the staff, training of basic principle, equipment, operation, maintenance issues of software comprehension and application, makePersonnel can operate independently equipment for the detection, sample analysis, and can perform basic maintenance.Four, the warranty commitment:1, equipment for one year warranty, life-long service, within one year of the non-human damage parts replaced free of charge, the warranty period the user received the invitation, the latest response time is 2 hours, and the user to confirm the fault, we will within 48 hours to send engineers to arrive at the sceneThe free service, find out the fault location and fault reason as soon as possible, and to users timely report failures and troubleshooting.2, the warranty period within the damaged parts procurement according to the price change (processing).3, the warranty to provide quality technical services for the user, after receiving repair invited users within 3 days after the arrival of users send engineers on-site repair. And enjoy the preferential purchase fittings treatment.The 4 sensor circuit, overload and overpressure damage not covered under warranty.
 


免责声明:以上所展示的信息由企业自行提供,内容的真实性、准确性和合法性由发布企业负责,智能制造网对此不承担任何保证责任。

在线询价

 

北京北广精仪仪器设备有限公

型:
生产厂家
联系人:
陈丹

联系我时,请说明是在智能制造网上看到的,谢谢

商家概况

主营产品:
电压击穿试验仪,体积电阻率表面电阻率测试仪,介电常数介质损耗测试仪,海绵泡沫压陷硬度试验仪,海绵泡沫塑料落球回弹试验仪,介电击穿强度试验仪
公司性质:
生产厂家

该商家其它产品

20Hz介电常数测定仪

20Hz介电常数测定...

摘要:20Hz介电常数测定仪具有多 [详细]
大变形拉力机

大变形拉力机...

摘要:大变形拉力机试验力、变形 [详细]
液体增塑剂体积电阻率的测定仪

液体增塑剂体积电...

摘要:液体增塑剂体积电阻率的测 [详细]
绝缘子层压材料电压击穿试验仪

绝缘子层压材料电...

摘要:绝缘子层压材料电压击穿试 [详细]
树脂陶瓷工频电压击穿试验仪

树脂陶瓷工频电压...

摘要:树脂陶瓷工频电压击穿试验 [详细]
热变形软化维卡温度检测仪

热变形软化维卡温...

摘要:热变形软化维卡温度检测仪 [详细]
ptfe泡点完整性测试仪

ptfe泡点完整性测...

摘要:ptfe泡点完整性测试仪复杂 [详细]
完整性测试仪3Q审计

完整性测试仪3Q审...

摘要:完整性测试仪3Q审计单纯泡 [详细]

其它商家同类产品


新手指南
了解智能制造卖家注册买家注册操作指南手机智能在线
旗下子站
智能控制机器人物联网3D打印
站点导航
找资讯找公司找产品找展会品牌商城
本站服务
会员服务企业建站广告服务SEO优化