产品详情
日本横河ALF111-S51通信模块
ALF111-S51通迅卡 重量0.4公斤
Item | Speci?cations |
Model | ALF111 |
Interface | FOUNDATION fieldbus (low speed voltage mode) 4 ports (1 segment (*1) per port) |
Transmission speed | 31.25 kbps |
Withstanding voltage | From ?eld to system: 1500 V AC/minute |
Bus connection (external connection) | • Pressure clamp terminals (removable terminal block with built-in terminators that can be switched on/off. • Connects with terminal board via a dedicated cable. |
Installation method | Mounted on ANB10£, ANB11£, ANR10£, AFF50£, AFV30£, AFV40£, or AFV10£ |
No. of control I/O channels (*2) | Max. 48 points/segment (Complies with high- and medium-speed scanning cycle by specifying up to 6 points of I/O points as high-speed scanning type on the ER bus.) |
No. of ?eldbus devices | Max. 32 units per segment (*3) (ALF111 counts as one unit) (*4) |
Communication functions | LAS function, Clock master function |
Dual-redundancy | Enabled to set up two units of ALF111 installed in the annexed slots in the same node unit. |
Current consumption | 0.5 A or less |
Weight | 0.4 kg |
The Ethernet communication module (ALE111) hardware speci?cations are as shown below.
Table Ethernet communication module hardware speci?cations
Item | Speci?cations |
Physical layer interface | IEEE802.3 10BASE-T |
Connection method | Point-to-point |
Connector | RJ-45 |
Transmission method | Half-duplex |
Transmission speed | 10 Mbps |
Transmission route | 100 ohm twisted-pair cable (not shielded) |
Transmission distance | 1 segment, 100 m (in between FCS and subsystems, or HUB and subsystems) |
Installation method | Mounted on ANB10£, ANB11£, ANR10£, AFF50£, AFV10£, AFV30£, or AFV40£ |
No. of ports | One port |
Media access control | CSMA/CD |
Communication functions | Communications with FA-M3, Modbus, MELSEC, YFGW, DARWIN/DAQSTATION, and PLC-5/SLC500 |
Current consumption | 0.5 A |
Weight | 0.3 kg |
An FCS collects data from subsystems or sets data with control calculations to subsystems using the builder functions by way of Ethernet communication modules. Only one communication function is established for each communication module, and multiple communication functions cannot be performed.
DCS培训教材
横河一个操作站HIS支持双显示屏连接,在一个操作站上同时可以在二个显示屏上显示不同的窗口,以增加每个操作站的操作能力。
Whole Plant Equipment Unit
操作员可以通过操作员站键盘或鼠标对连在HIS上的二个显示器上不同的流程图,或控制面板或趋势图或报.警信息进行操作。这样可以大大的提高一个HIS的利用率,同时提高操作效率。
横河电机的DCS系统自采用计算机技术以来就解决了中文输入的问题。由于横河电机本身在日本做系统开发的过程中间就要解决英语操作系统,日语使用界面问题。所以对横河的DCS产品来说,在YEWPACK时期就已经解决了跨语言问题。所有在中国市场上销售的大规模DCS系统CENTUM-XL/CENTUM-CS/CENTUM-CS3K R2,都具备中文显示的能力,在这个问题上从来是得到中国用户的认可和好评ALF111-S51通信模块。
随着计算机水平的发展,横河DCS产品的汉字输入也一直在进步,输入越来越快,越来越方便。横河的DCS系统中所有可以实现二次开发,由组态工程师输入的部分,都可以依据用户的需要而直接输入汉字。例如:仪表注释;流程图画面等供操作人员使用的界面中全部可以直接使用中文WINDOWS的汉字输入方法调用中文WINDOWS的汉字字库,并在操作员站上做直接显示。
PRM(PLANT RESOURCE MANAGER)工厂资源管理服务器ALF111-S51通信模块 随着现场总线和智能仪表技术的发展,双向的全数字化的通讯已经越来越标准化和。 横河电机不仅可以提供现场总线的仪表,还能够提供支持现场总线的系统。PRM软件包就是横河电机提供的一个有效管理现场设备的软件,主要是面向工厂的仪表维护人员和工艺运行人员,可以有效的减少工厂的整体成本。
现场控制站ALF111-S51通信模块 此竞标书中所提供的现场控制站(FCS)是横河电机新一代的控制站。它集过程控制功能、计算机和批量控制过程为一体。对过程数据采用循环扫描的方式,每个功能块的循环扫描周期可以单独定义,从50ms到1s。
控制站FCS所有的模件都采用集成度高、散热量低的固态电路以及表面封装技术,防尘、抗*力强,适合各种恶劣的运行环境。模件的编址与物理位置的对应关系简单明了,容易掌握。模件带电插拔不会引起本模件故障,也不会影响其它模件的正常工作。模件插拔都有导轨和联锁装置,防止损坏或引起故障。模件通用性强,种类规格少,有效地减少了备品备件的费用支出ALF111-S51通信模块
DCS的通讯网络
本系统的网络结构分为主网,支网和I/O 网络,详见网络结构图:
主干网络是连接各控制室和*控制室监控计算机的网络,采用冗余工业以太网,通讯速率 10/100Mbps,此网络是*的工业控制网络,具有速度快,效率高,数据实时性好,抗干扰性强,符合自动化系统发展的需要等特点。