南澳电气NASF6高精度SF6气体放电分解物分析仪

NASF6 High Accuracy SF6 Discharge Analyzer

1.1  南澳电气NASF6高精度SF6气体放电分解物分析仪功能概述

  南澳电气NASF6高精度SF6气体放电分解物分析仪提供了一种简单的SF6分解产物现场检测方法。使用过程中，连接到一个带压的充有SF6气体设备的气室中，让SF6气体以一定流速流过传感器，直接测量到SF6气体中主要分解产物的含量。全部采用SF6传感器，长寿命设计，保证了测量结果的准确性和重现性。主要应用：故障定位，例行检测，局部放电监测，气体净化/过滤监测，故障高压接点检查，SF6分解产物检测，检查开关内分解产物的产生。

1.2南澳电气NASF6高精度SF6气体放电分解物分析仪主要特点

●长寿命探测组件

●无需比色管、传感器直接测量

●优秀的准确性和重现性

●精确高，重复性好

●内置稳压阀和电子质量流量计

●超大液晶显示

●轻巧便携容易使用

●充电电池供电，交直流两用

●响应快，几乎无预热等候

●测量结果不受环境温度影响

1.3  南澳电气NASF6高精度SF6放电分解物分析仪技术指标

测量范围：SO2：0～100 PPM；H2S：0～100 PPM

灵 敏 度：SO2：±0.1 PPM；H2S：±0.1 PPM 响应时间： 25s取    样： 内置流量阀、流量计；

3.6米取样管和减压阀接头一只。工作温度： -10℃～+50℃电    源： 直流：内置充电池，交流：220V／50Hz；读    出： 超大液晶图形化显示；尺    寸： 258(mm)×240(mm)×88(mm)；重    量： 2.6公斤；输出接口： USB1.2规范（可以选购配置）；取样流量： 0.01~1L/min，*流量：0.25L/min。

1.1 Functional Overview

NASF6 decomposition product analysis tester, provides a simple SF6 decomposition products on-site detection method. In use, the SF6 gas is connected to a gas-filled SF6 gas chamber, allowing SF6 gas to flow through the sensor at a constant flow rate to directly measure the amount of main decomposition products in the SF6 gas.

All sensors use SF6-specific sensors, long-life design, to ensure the accuracy and reproducibility of measurement results.

Main applications: fault location, routine testing, partial discharge monitoring, gas purification / filtration monitoring, fault high voltage contact inspection, SF6 decomposition product detection, check the switch decomposition products.

1.2 Main features

● Long-life detection components

● No colorimetric tube, the sensor is directly measured

● Excellent accuracy and reproducibility

● High precision, good repeatability

● Built-in regulator and electronic mass flowmeter

● Large LCD display

● Lightweight and easy to use

● rechargeable battery-powered, AC-DC dual-use

● fast response, almost no warm-up waiting

● The measurement results are not affected by the ambient temperature

1.3 Technical Specifications

Measuring range: SO2: 0 ~ 100 PPM; H2S: 0 ~ 100 PPM

Sensitivity: SO2: ± 0.1 PPM; H2S: ± 0.1 PPM

Response time: 25s

Sampling: built-in flow valve, flow meter;

3.6 m sampling tube and a pressure reducing valve connector.

Operating temperature: -10 ℃ ~ +50 ℃

Power supply: DC: built-in rechargeable battery, AC: 220V / 50Hz;

Read out: large LCD graphic display;

Size: 258 (mm) × 240 (mm) × 88 (mm);

Weight: 2.6 kg;

Output interface: USB1.2 specification (optional configuration);

Sampling flow: 0.01 ~ 1L / min, recommended flow: 0.25L / min.